Your Selected Vehicle
Parts for your 1989 Toyota Hilux surf-Headlights
OEX 6mm Twin Core Automotive Cable, Red/Black, With Black Sheath - 5m Blister Pack (NZ Ref. 157) - ACX0811-5BL
Narva Battery Master / Isolation Switch Plastic With Removable Key (Contacts Rated 100A at 12V) - 61038BL
LED Autolamps LED Autolamps Front Indicator/Position LED Light Clear Lens 12v Twin Blister Pack - 175AW/2
OEX Crimp Terminal Female Blade Brass Terminal Entry 6.3 x 0.8mm Non Insulated 100 Pce - ACX3078
OEX Crimp Terminal Female Blade Blue Terminal Entry 6.3 x 0.8mm Heat Shrinkable 50 Pce - ACX3168
OEX Rocker Surface Mount Switch On/Off SPST 12V Blue Illuminated (contacts Rated 30A @ 12V) - ACX1973BL
1989 Toyota Hilux Surf headlights — what they do and how to look after them
Headlights absolutely are fitted and relevant on the 1989 Toyota Hilux Surf. Technical documentation backs this: the Toyota Electrical Wiring Diagram (EWD) for 1989 4Runner/Hilux Surf details the headlamp circuits and dimmer relay, Toyota’s Repair Manual for the N130 series (Body Electrical—Lighting) covers the headlamp assemblies and service steps, and Australian Design Rules ADR 13/00 and ADR 46/00 (and NZ WOF/VIRM guidance) require compliant headlamps for road use. Depending on market and trim, this model came with either 200 mm rectangular sealed-beam units or composite housings running H4 60/55 W halogen bulbs.
On a Surf, the headlights pull double duty: bright, reliable forward visibility on low and high beam, and a legal, well-controlled beam pattern that won’t dazzle oncoming traffic. They’re switched via the column stalk and dimmer relay, protected by fuses, and grounded to the body—so clean connections and proper voltage matter as much as the bulb itself.
As part of regular servicing, it’s smart to:
- Inspect lenses for UV haze, cracks or moisture, restore or reseal as needed.
- Check aim. Mis-aimed lights are common WOF/rego fails, adjusters are on the lamp frame.
- Test voltage at the bulb, high resistance in old switches or earths causes dim output.
- Replace bulbs in pairs and stick with ADR-compliant halogen H4 or approved sealed-beam units.
Handy replacement tips for the Surf crowd:
- Confirm what you’ve got: look for “H4” on the back cap (composite) or a sealed-beam face marking.
- For H4: unplug, remove the rubber boot, unclip the spring, swap the bulb (don’t touch the glass), refit in the same orientation.
- For sealed-beam: remove the retainer ring, unplug, fit the new unit, and re-aim.
- After any lamp work, set beam aim on level ground—centre of the cut-off should sit slightly below headlamp centre height at a few metres back.
If output still feels a bit average, a relay upgrade harness, cleaned earths, and quality bulbs can lift brightness without breaking ADR rules. Steer clear of plug-in HID/LED retrofits in the original reflector housings unless the entire assembly is approved for road use.
Popular questions
What bulb type fits a 1989 Hilux Surf?
Many N130 Surfs use H4 60/55 W halogen bulbs in composite headlights, while some markets received 200 mm sealed-beam units. Check the lamp marking (“H4” vs sealed-beam code) or the Toyota parts listing for your VIN to be sure.
How can brightness be improved legally?
Start with new quality halogen H4s or fresh sealed beams, clean grounds, and consider a proper relay harness to reduce voltage drop. Restore hazy lenses and re-aim. Only use ADR-compliant LED or complete replacement lamps if upgrading technology.
How often should headlight aim be checked?
Give it a look every service or after any front-end work, bulb change, or suspension/lift changes. Mis-aim is a common WOF/regulatory fail and a quick tweak keeps night driving safe.