Parts for your 2024 Toyota Camry-Sump plug washers

2024 Toyota Camry sump plug washer: purpose, replacement and servicing

Yes, the 2024 Toyota Camry is fitted with a sump plug washer (oil drain plug gasket). Toyota technical documentation confirms it’s required: the Toyota Electronic Parts Catalogue (EPC) lists a “Gasket, drain plug” for the XV70-series Camry (AXVA70 2.5L, AXVH70 hybrid, GSV70 V6), commonly supplied as an aluminium 12 mm crush washer (Toyota part no. 90430-12031). The Toyota Repair Manual for the XV70 platform also instructs to install a new drain plug gasket at each engine oil change and to tighten the plug to the specified torque (around 39 N·m, check the exact value for the specific engine/market). So a sumpplugwashers is absolutely relevant on a 2024 Toyota Camry.

What does it do? The sump plug washer is a small, single-use sealing ring that sits between the Camry’s oil pan and the drain plug head. When the plug is tightened to spec, the soft aluminium crushes microscopically to create a leak-tight seal, even as the engine heats up and cools down. It also helps achieve consistent clamping without over-stressing the threads in the alloy pan—handy insurance against drips and expensive repairs.

When should it be changed? Best practice—echoed in Toyota service procedures—is to replace the washer at every oil change. Re-using a crushed washer can lead to weeping around the plug, especially after a few heat cycles or longer runs. If there’s fresh oil mist on the lowest edge of the pan or a drop forming at the plug after parking, it’s time for a new washer and a re-torque to spec.

How should it be fitted? Keep it simple: drain the oil, remove the old washer from the plug, wipe the mating face on the sump clean and flat, slide on a new genuine-equivalent aluminium washer, and reinstall the plug to the correct torque with a quality torque wrench. No sealants are needed—if the surface is clean and the washer is new, it will seal. After refilling with the right grade and volume of oil, run the engine, then check underneath for any sign of seepage.

• Use a genuine Toyota or equivalent 12 mm aluminium crush washer (commonly 90430-12031).
• Replace at each service interval (typically 12 months/15,000 kilometres in AU/NZ, or as per the logbook).
• Confirm the torque for your engine variant, many XV70 Camry engines specify about 39 N·m.
• If the plug or sealing face is nicked or burred, replace the plug and lightly dress the face before refitting.

Do that, and the Camry’s sump plug will stay bone-dry between services—no dramas, no stains on the driveway, and the engine stays well protected.

Does the 2024 Toyota Camry use a sump plug washer?

It does. Toyota’s EPC lists a drain plug gasket for the 2024 Camry across 2.5-litre petrol, hybrid, and V6 variants, typically the aluminium crush washer 90430-12031. The Repair Manual calls for a new gasket any time the oil is drained and the plug is refitted.

It’s a single-use seal designed to crush once and maintain clamping force. Re-using it risks seepage after a few heat cycles, so fresh washer, correct torque, and you’re sorted.

How often should the sump plug washer be replaced on a 2024 Camry?

Every oil change. That aligns with Toyota’s service guidance to renew the drain plug gasket whenever the plug is removed. In Australia and New Zealand that’s generally every 12 months/15,000 kilometres, or as shown in the owner’s logbook.

If the plug has been off between services—say for an inspection or repair—fit a new washer then as well. It’s a cheap part that prevents leaks and protects the alloy sump threads.

What size is the 2024 Camry sump plug washer and what torque should be used?

The washer used is typically a 12 mm ID aluminium crush type (Toyota 90430-12031). It’s made to match the Camry’s drain plug and sump seat profile, so going by the correct part number or VIN is smartest.

Torque is commonly specified around 39 N·m on XV70 Camry engines, but always confirm the exact figure for your engine code in the service manual. Tight, but not over-tight—let the washer do the sealing.