Your Selected Vehicle
Parts for your 2013 Ford Transit-Headlights
LED Autolamps 24V Front Indicator And Park Light Chrome Bezel Blister Pack - 285CAW24
LED Autolamps 12V Stop/Tail/Indicator/Licence Plate Lamp With Reflector - 149BARL4P
LED Autolamps 174 Series Stop/Tail/Indicator Lamp 12/24V, Surface Mount, 40cm Cable - 174ARMB
LED Autolamps 174 Series Stop/Tail Lamp 12/24V, Surface Mount, 40cm Cable - 174RMB
Explore 4WD & Adventure
LED Autolamps 174 Series Reverse Lamp 12/24V, Surface Mount, 40cm Cable - 174WMB
LED Autolamps Licence Plate Lamp Black Bracket Multi Volt With 1m Cable - 35BLM1P
LED Autolamps 10/30V LED Side Direction Indicator Light With 30cm Wire - 35AMB
LED Autolamps 12V Stop/Tail Lamp Black Chrome Round With Clear Lens - 102RBC
LED Autolamps 12V 82 Series Stop/Tail/Indicator/Reverse Lamp Black Bracket - 82BARW
LED Autolamps Multi Volt Stop/Tail/Indicator With 18 Square LEDs Twin Blister - 135ARM/2
LED Autolamps 12/24V Stop/Tail/Indicator/Reverse Assembly 3 Lamps With 153 LEDs - 125BARWM
LED Autolamps 12/24 Multi Volt Stop/Tail/Indicator/Reverse Assembly Lamp With 108 LEDs - 80BARWM
LED Autolamps 12V Front Indicator Amber Lens Black Base Twin Blister Pack - 175A/2
LED Autolamps LHS, Stop/Tail/SEQ-Indicator/Reverse/Reflector 12/24V 284 X 100 X 37mm, DT04 Connector - SO284LHS
LED Autolamps 12/24V LED Reverse Lamp Screw Surface Mount Blister Pack - 12WM-2
LED Autolamps 12/24V Reversing Lamp With 25 White LEDs With Bracket and 30cm Wire - 100WM
2013 Ford Transit Headlights
Headlights are absolutely fitted to the 2013 Ford Transit and are mandatory for road use. This is confirmed by Ford’s Transit Owner’s Manual and Workshop Manual (Section 417-01: Exterior Lighting), along with Australian Design Rule 13/00 and the NZ Land Transport Rule: Vehicle Lighting 2004, which require compliant headlamps on vehicles of this class. So yes—headlights are relevant, standard, and essential on a 2013 Ford Transit.
On a 2013 Transit, the headlights do the heavy lifting after dark and in poor weather, helping the driver see the road, hazards and signage while making the van more visible to everyone else. Most 2013 Transit variants use halogen lamps, many standard vans run an H4 bulb (low/high in one), while some Transit Custom models from the same year may use separate H7 low beam and H1 high beam. Always confirm bulb type in the owner’s manual or on the lamp housing label.
As part of regular servicing, it’s smart to give the headlights a once-over. Bulbs gradually dim with age, so replacing in pairs keeps the beam colour and brightness consistent. If a bulb’s out, avoid touching the glass with bare fingers—skin oils can shorten bulb life. Check headlight fuses and relays if both sides go dark, and look for signs of moisture in the lens, light fogging can be normal after rain, but persistent water droplets call for resealing or a new unit to protect the reflector and wiring.
Correct aim matters for both ADR/WOF compliance and good night vision. After any bulb or headlamp replacement, get the aim checked and adjusted on a level surface using the factory adjusters. Keep the lenses clean—road film can cut output dramatically—and consider a quick polish if UV haze appears. If upgrading to higher-performance halogens, stick to legal wattage and E-marked bulbs for Aussie and Kiwi roads.
- Typical service checks: operation (low/high), lens condition, aim, wiring/connector security, and fuse integrity.
- Replacement tips: confirm bulb type, replace in pairs, don’t touch glass, test and re-aim.
- If fitted with DRLs, make sure they illuminate correctly and don’t substitute for low beam at night.
Popular questions about 2013 Ford Transit headlights
What headlight bulb does a 2013 Ford Transit use?
Most 2013 Transit vans use an H4 halogen for combined low/high beam, while some Transit Custom variants use H7 low beam and H1 high beam. Because trims differ by market, always check the owner’s manual or the marking on the back of the headlamp for the exact bulb spec and wattage.
How do you adjust the headlight aim on a 2013 Transit?
Park on level ground facing a flat wall, measure and mark the beam height, then use the headlamp adjusters on the housing to set vertical and horizontal aim to spec. After any bulb or headlamp change, aim should be verified to meet ADR/WOF requirements and to avoid dazzling other road users.
Why is there condensation in the headlight?
Light misting after wet or cold weather can be normal and often clears with driving. If water droplets or pooling persist, the venting or seal may be compromised. Inspect caps and seals, if moisture remains, repair the seal or replace the unit to protect the reflector, wiring, and bulb life.