Your Selected Vehicle
Parts for your 2005 Toyota Vitz|yaris-Headlight bulbs
LED Autolamps 12V Round Indicator Lamp With Amber Lens Recessed Mount 130mm Diameter - 102A
LED Autolamps Twin Function Stalk Side Indicator With Red/Amber Side Marker LHS Multivolt - 805ARIML
LED Autolamps Multi Volt Rear Indicator Lamp With 8 Square LEDs Blister Pack With Black Base - 135AM
LED Autolamps Interior LED Light 12v Blue Lens Chrome Housing 10cm Cable Blister Pack - 68B
Explore 4WD & Adventure
LED Autolamps 12V Blue Courtesy Lamp Super Small Design Twin Blister Pack - 16B12-2
LED Autolamps 275GARWM + 2 X LR12 + 450mm Loom DT04 Connector And 500mm LP Cable - SO275GARWM2LR450
LED Autolamps 12V Stop/Tail/Indicator/Reverse With Reflectors And 500mm LP Cable - SO283ARWM2LR12
LED Autolamps 12/24 Multi Volt Stop/Tail/Indicator/Reverse Assembly Lamp With 108 LEDs - 80BARWM
LED Autolamps 12/2V Maxilamp LED Stop/Tail/Indicator/Reflector Black Chrome Bolt Mount - MAXILAMPC1XCE
LED Autolamps 12V 82 Series Stop/Tail/Indicator/Reverse Lamp Black Bracket - 82BARW
LED Autolamps 12/24V Reverse Lamp Horizontal/Vertical Mount Twin Blister - 11WM-2
LED Autolamps Multi Volt Stop/Tail/Indicator Lamp 190x95x28mm Blister Pack - 280ARM
LED Autolamps Traffic Advisory Light Red LED 12v Only Red Lens 10cm Cable Boxed - 83R
LED Autolamps 174 Series Stop/Tail Lamp 12/24V, Surface Mount, 40cm Cable - 174RMB
2005 Toyota Vitz/Yaris Headlight Bulbs
Based on technical sources including the Toyota Repair Manual for the XP90 platform, the 2005 Toyota Vitz/Yaris Owner’s Manual, and industry bulb catalogues from OE suppliers (e.g., Koito, Philips), this model uses replaceable halogen headlight bulbs. Depending on market and headlamp design, it’s typically either an H4 dual‑filament bulb (low/high in one) or separate bulbs such as 9006/HB4 for low beam and 9005/HB3 for high beam. The headlight bulbs are therefore absolutely relevant and serviceable items on a 2005 Toyota Vitz/Yaris.
The headlight bulbs do the grunt work of throwing a safe, legal beam pattern so the driver can see the road and be seen by others. In a 2005 Toyota Vitz/Yaris, the reflectors and lens are designed around halogen bulbs, so correct wattage and base type matter for visibility, ADR/WOF compliance, and not cooking the housing.
As halogens age, they go dull and yellow before they finally blow. Owners will often notice the light output drop off at night, especially in wet weather. It’s smart practice to replace in pairs every 3–5 years or roughly 60,000–100,000 km, even if one’s still working. Keep the lenses clean, check for moisture inside the housing, and don’t touch the glass when fitting new bulbs—skin oils can shorten bulb life. After any bulb change, verify the beam aim to avoid dazzling oncoming traffic and to pass WOF/regos without drama.
Replacement is straightforward on most 2005 Toyota Vitz/Yaris variants: pop the bonnet, unplug the connector, release the rubber boot and spring clip (H4) or twist-lock (HB3/HB4), swap the bulb like-for-like, and refit in reverse. Stick with the specified wattage (commonly 60/55 W for H4, or 55 W for HB3/HB4). If the headlights still seem dim after fresh bulbs, the issue might be cloudy lenses or a poor earth connection rather than the bulbs themselves.
- Signs it’s time to replace: dim or yellow output, one side out, flickering, or mismatched colour.
- Tip: Keep a spare matched pair in the glovebox for road trips.
What headlight bulb fits a 2005 Toyota Vitz/Yaris?
Most use an H4 dual‑filament bulb, while some markets/models use HB4 (9006) low beam and HB3 (9005) high beam. The exact type is printed on the back of the headlamp housing and listed in the owner’s manual. It’s best to match the build date and lamp markings before buying.
How often should the headlight bulbs be changed?
Replace when dim or failed, and consider preventative replacement every 3–5 years or 60,000–100,000 km. Halogens slowly lose brightness over time, so changing both sides together keeps the beam colour and intensity even.
Can they upgrade to LED bulbs?
Retrofit LED bulbs in halogen housings can affect beam pattern and may not meet ADR/NZS compliance, risking WOF failure or glare to others. If considering LEDs, choose compliant kits proven in this headlamp type, or stick with quality halogen upgrades designed for road use.