Your Selected Vehicle
Parts for your 2003 Mitsubishi Pajero-Headlight bulbs
LED Autolamps 12/24V Stop/Tail/Indicator/Reverse Lamp 460x130x33mm - 460ARWM
LED Autolamps Licence Plate Lamp Black Bracket Multi Volt With 1m Cable - 35BLM1P
Explore 4WD & Adventure
LED Autolamps 174 Series Stop/Tail Lamp 12/24V, Surface Mount, 40cm Cable - 174RMB
LED Autolamps 174 Series Stop/Tail/Indicator Lamp 12/24V, Surface Mount, 40cm Cable - 174ARMB
LED Autolamps Tray Conversion Kit To suits Hilux Contains Two Cables - PATCH-HILUX
LED Autolamps 174 Series Reverse Lamp 12/24V, Surface Mount, 40cm Cable - 174WMB
LED Autolamps 12/24 Multi Volt Stop/Tail Lamp 36 LEDs With 40cm Wire - 80RM
LED Autolamps 12/24V Round Stop/Tail Lamp With Clear Lens 130mm Diameter Recessed Mount Blister Pack - 102RCM
LED Autolamps 12V Stop/Tail/Indicator/Licence Plate Lamp With Reflector - 149BARL4P
LED Autolamps Twin function rear position with supplementary rear indicator - 97RIM
LED Autolamps 12V/24V Round LED Stop/Tail Lamp With Grommet and Plug - 110RMG
LED Autolamps 12V 82 Series Stop/Tail/Indicator/Reverse Lamp Black Bracket - 82BARW
LED Autolamps 12/24V LED Reverse Lamp Screw Surface Mount Blister Pack - 12WM-2
LED Autolamps Multi Volt Stop/Tail/Indicator With 18 Square LEDs Twin Blister - 135ARM/2
2003 Mitsubishi Pajero headlight bulbs
Based on technical references such as the 2003 Mitsubishi Pajero owner’s manual (NM/NP series), Mitsubishi ASA parts catalogues, and major bulb-fitment guides from Osram and Philips, this model is fitted with replaceable halogen headlight bulbs. Many 2003 Pajero variants use an H4 dual‑filament globe for combined low/high beam, while some trims use separate bulbs (commonly HB3/9005 for high beam and H1 or H7 for low beam). Checking the owner’s manual or the sticker behind the headlamp cover under the bonnet will confirm the exact fitment.
The headlight bulbs do the heavy lifting after dark—helping the driver see the road ahead and making the Pajero visible to others. They’re also key to passing WOF/CoF or roadworthy checks across Australia and New Zealand. As halogen bulbs age, light output drops and the colour shifts, so even before a globe fails, visibility can suffer. Replacing bulbs in pairs keeps beam colour and brightness matched side to side.
Good servicing practice is to inspect the Pajero’s headlight operation at each service interval and before long trips. Look for dim, flickering, or yellowed light, haze in the lens, moisture inside the housing, heat damage on connectors, and brittle rubber caps. If upgrading bulb performance, stick with ADR-compliant options and ensure beam aim is checked afterwards.
- Confirm bulb type: Check the manual or existing bulb markings (e.g., H4, HB3, H1, H7).
- Power off: Switch ignition and lights off, disconnect the battery if desired.
- Access the rear cover: Remove the rubber cap or plastic lid behind the headlamp.
- Release the clip or twist-lock: Note the bulb orientation.
- Install the new bulb: Avoid touching the glass, use gloves. Seat it fully and secure the clip.
- Reconnect and test: Verify low and high beam, then adjust aim if needed.
- Replace in pairs to keep brightness even.
- Clean the lens exterior, cloudy lenses cut output dramatically.
- Use dielectric grease on connectors if they’re exposed to moisture.
- If fuses blow or bulbs fail early, have charging voltage and earths checked.
FAQs
What bulb type fits a 2003 Mitsubishi Pajero?
Most 2003 Pajero variants use an H4 dual‑filament globe. Some trims run separate high/low beams, typically HB3 (9005) for high and H1 or H7 for low. Always verify against the owner’s manual, the label behind the headlamp cover, or a reputable bulb catalogue for the exact variant.
How often should the headlight bulbs be replaced?
Halogen bulbs gradually dim, so many owners replace them every 3–5 years or at the first sign of reduced brightness, yellowing, or flicker. Replace in pairs and recheck headlight aim after fitting.
Can the Pajero’s halogen bulbs be upgraded to LED?
Retrofit LEDs may not be legal in halogen reflector housings unless the headlamp assembly is certified to the relevant ADR/NZTA standards. If considering LEDs, confirm compliance, beam pattern, and aim. For a simpler, legal boost, choose premium halogen upgrades that meet ADR requirements.