Your Selected Vehicle
Parts for your 1993 Nissan Primera-Headlights
LED Autolamps Twin function side indicator with amber/red side marker - 97CARIMCSB
LED Autolamps Multi Volt Stop/Tail/Indicator Assembly 72 LEDs With Black Bracket 190x100x28mm - 80BARM
Explore 4WD & Adventure
LED Autolamps 12V Stop/Tail/Indicator/License Plate Boat Trailer Lamp, Right Side - 207BARL4P
LED Autolamps 385 Series Rear Combination Lamp RHS with 7 core plug - 385ARWMRCSB
LED Autolamps 12V Stop/Tail/Indicator Lamp Reflector With 4 Pin Plug - 149BAR4P
LED Autolamps LED Side Direction Indicator With Reflector 135x38x22mm - 38AM
LED Autolamps 12V/24V Maxilamp 5 Lamp Combination Stop/Tail/Indicator/Reverse/Reflector - MAXILAMPC5XRW
LED Autolamps Multi Volt Amber LED Side Marker 3 SMD LEDs Blister Pack - 181AME
LED Autolamps Tray Conversion Kit to Suit Ford Ranger/ Mazda BT-50 Contains Two Cables - PATCH-RANGERBT50
LED Autolamps Tray Conversion Kit To suits Hilux Contains Two Cables - PATCH-HILUX
LED Autolamps Multi Volt Stop/Tail Lamp With Rubber Grommet And Plug - 164RM
LED Autolamps 24V Front Indicator And Park Light Chrome Bezel Blister Pack - 285CAW24
LED Autolamps 12/24V Cat6 Side Direction Indicator Clear Lens Blister Pack - 77ACM
LED Autolamps 12/24V Stop/Tail/Indicator/Reverse Lamp 460x130x33mm - 460ARWM
LED Autolamps 12/24V Reverse Lamp Horizontal/Vertical Mount Twin Blister - 11WM-2
LED Autolamps 12/24V Front End Outline Marker Recessed Fitting Twin Blister - 7922WM2
LED Autolamps 12V Stop/Tail/Indicator/Licence Plate Lamp With Reflector - 149BARL4P
LED Autolamps Multi Volt Stop/Tail/Indicator Lamp With Reflex Reflectors Grey Base Blister Pack 1 pce - 100ARM
LED Autolamps 174 Series Stop/Tail/Indicator Lamp 12/24V, Surface Mount, 40cm Cable - 174ARMB
1993 Nissan Primera headlights
Headlights are absolutely fitted to and relevant for the 1993 Nissan Primera (P10). This is documented in the Nissan Primera P10 factory service manual and owner’s manual lighting sections, and required by Australian Design Rules (ADR 13/00 and ADR 46/00) as well as New Zealand’s Land Transport Rule: Vehicle Lighting 2004. Those technical sources mandate compliant headlamps for safe road use, so this model ships with halogen headlights from factory.
On a ’93 Primera, the headlights do the heavy lifting for night driving and poor weather, projecting a legal beam pattern suited to right-hand-drive markets like Australia and New Zealand. The units are halogen reflector lamps, typically using an H4 60/55W dual‑filament bulb for low and high beam in one globe. Keeping them in good nick means better visibility, less fatigue, and a happier WOF or rego inspection.
When it’s time to replace a bulb, it’s a straightforward job under the bonnet. Access the rear of the headlamp, pop off the dust cap, unclip the spring retainer, and swap the H4 globe. Don’t touch the glass with bare fingers—oils shorten bulb life. Refit carefully, ensuring the rubber boot seals out moisture. It’s smart to replace bulbs in pairs so colour and brightness match. Stick with the factory wattage, higher-watt globes can overheat wiring and may not be ADR-compliant.
Routine care goes a long way. If the lenses have gone cloudy or yellow, a quality plastic headlight restoration kit can restore clarity—finish with a UV sealant to keep the haze away. Check connectors and earths for corrosion, a dodgy ground or voltage drop will make lights dim. If light output still feels weak after fresh bulbs and clean lenses, have the charging system tested and the headlight aim checked using proper equipment.
- Use ADR/UNECE-compliant H4 halogen bulbs for AU/NZ.
- Keep lenses clean, restore and seal if they’re hazed.
- Inspect fuses, connectors, and earth points during servicing.
- Have a workshop or WOF station verify beam aim and pattern.
What bulb type fits a 1993 Nissan Primera headlight?
Most P10 Primeras use an H4 60/55W halogen for combined low/high beam. Parking/position bulbs are usually W5W (T10). Always confirm against the owner’s manual or the existing bulb, as trims and markets can vary. Avoid non-approved HID/LED retrofits that can breach ADR/WOF requirements.
How does one adjust the headlight aim?
Use the vertical and horizontal adjusters on the back of each lamp. Park on level ground facing a wall, mark the cut-off, and make small changes. For best results—and to stay compliant—have a workshop or WOF inspector set the aim with a beam setter to the specifications in the service manual.
Why are the headlights dim or yellow?
Ageing halogen bulbs, UV-hazed plastic lenses, corroded earths, or voltage drop in old connectors are common culprits. Fit fresh quality H4 bulbs, restore the lenses with a sealant, and clean or repair wiring and grounds. If brightness is still off, get the alternator/charging voltage and beam aim checked.