Your Selected Vehicle
Parts for your 2023 Suzuki Splash-Batteries
Narva Push Button Starter Switch On/Off Momentary SPST Red LED (Contacts Rated 50A @ 12V) - 60099BL
Narva Heavy Duty Rocker Switch Momentary On/Off/Momentary On DPDT (Contacts Rated 20A @ 12V) - 63044BL
Explore 4WD & Adventure
Drivetech 4x4 Rocker Beacon Switch On/Off SPST 12 or 24V Blue Illumination (Contacts Rated 20A @ 12V) - DT-11012
Narva Sealed Rocker Switch Off/On SPDT 12V Blue Illuminated Backup Lights Symbol (Contacts Rated 20A @ 12V) - 63142BL
OEX Rocker Switch On/Off DPST 12V Driving Light, Illuminated (Contacts Rated 20A @ 12V) - ACX1960BL
Narva Sealed Rocker Switch Off/On SPDT 12V/24V Blue LED Illuminated Aux Lights Symbol (Contacts Rated 20A @ 12V) - 63232BL
Drivetech 4x4 Rocker Winch Switch Mom On/Off Mom On SPDT 12 or 24V Blue Illuminated (Contacts Rated 20A @ 12V) - DT-11007
OEX Rocker Surface Mount Switch On/Off SPST 12V Blue Illuminated (contacts Rated 30A @ 12V) - ACX1973BL
2023 Suzuki Splash Batteries
Based on technical sources including the Suzuki Splash Owner’s Manual (EU, 2013), Suzuki K10B/K12B workshop data, and AU/NZ battery fitment catalogues from Century Yuasa and Bosch (2023), the Suzuki Splash uses a 12‑volt automotive starting battery. Some market variants may feature idle‑stop systems that require enhanced batteries (EFB/AGM). So, batteries are absolutely relevant to a 2023 Suzuki Splash listing or service enquiry.
This little hatch relies on its battery for far more than starting. The 12‑volt unit wakes the ECU, fuels the ignition system, powers the fuel pump, stabilises voltage for ABS, EPS and safety systems, and keeps lights and accessories happy when the alternator’s not doing the heavy lifting. If the car has idle‑stop, the battery also endures frequent restarts, so spec matters.
For Aussie and Kiwi conditions, a healthy Splash battery should last around 3–5 years, depending on driving mix and heat. Common fitments in this class are JIS B24L footprint units in the 45–55 Ah, 330–410 CCA range, always match the exact size, terminal layout and rating on the vehicle’s label or in the owner’s book. If the vehicle is fitted with idle‑stop, stick with EFB (or AGM where specified). Don’t downgrade from EFB/AGM to a standard flooded battery.
When replacing, preserve memory with a support pack if possible, then remove the negative clamp first and refit it last. Seat the battery squarely, tighten the hold‑down, and lightly coat clean terminals with dielectric grease. After installation, check charging voltage at the posts (typical 13.8–14.7 V with the engine running). If the car has an idle‑stop or an intelligent battery sensor, perform the battery reset/registration with a scan tool or follow the maker’s relearn procedure to restore full stop/start function.
- Signs it’s time: slow cranking, dimming lights at idle, random warning lamps, idle‑stop disabled, or a swollen/smelly case.
- Good habits: weekly longer drives, keep the top clean and dry, avoid deep discharges, and use a smart maintainer during long sits.
Servicing shops should also load‑test during scheduled maintenance, verify parasitic draw is in spec, and inspect the earth strap. A correct‑spec battery, fitted and tested properly, keeps the Splash feeling sprightly every morning.
What battery size and type fits a 2023 Suzuki Splash?
Most Splash variants use a compact JIS B24L footprint with 45–55 Ah capacity and around 330–410 CCA. Exact specs vary by engine (1.0 or 1.2) and equipment. If the car has idle‑stop, choose an EFB (or AGM where specified). Always confirm with the under‑bonnet label or owner’s manual before buying.
How long will a Splash battery last in Australia or New Zealand?
Typically 3–5 years. Hot summers, short trips and accessories can shorten life. Regular testing at service time, keeping terminals clean, and using a maintainer during long storage all help it go the distance.
Does a Suzuki Splash need coding after a battery change?
Non idle‑stop models usually don’t need coding—fit the right spec and you’re set. If yours has idle‑stop or an intelligent battery sensor, perform a battery reset/registration with a scan tool or follow the maker’s relearn steps so charging strategy and stop/start work correctly.