Your Selected Vehicle
Parts for your 2019 Audi Q5-Headlight bulbs
LED Autolamps Rear Taillight Harness To Suit MY22 Ranger / MY20 Ram Plug To Bare Wires - PATCH-RAM.UNI
LED Autolamps 174 Series Stop/Tail Lamp 12/24V, Surface Mount, 40cm Cable - 174RMB
Explore 4WD & Adventure
LED Autolamps 12/24V 16 LED Stop/Tail Indicator Lamp Black Bracket Blister Pack - 201BSTIM
LED Autolamps 12V Interior Strip lamp Touch Sensor Switch With MCU Circuitry - 40260SMCU
LED Autolamps 12/24V Round Indicator Lamp With Clear Lens 130mm Diameter Recessed Mount - 102ACM
LED Autolamps Multi Volt Round Indicator Lamp With Amber Lens Recessed Mount - 102AM
LED Autolamps Multi Volt Stop/Tail/Indicator Lamp Black Bracket With 40cm Wire - 80BSTIM
LED Autolamps 24V Front Indicator And Park Light Chrome Bezel Blister Pack - 285CAW24
LED Autolamps Twin Function Stalk Side Indicator With Red/Amber Side Marker LHS Multivolt - 805ARIML
LED Autolamps 12/24V Amber Emergency Mini Light Bar Clear Lens With Amber LEDs 18 Selectable Flash Patterns Magnetic Mount - LB380ACMM
LED Autolamps Stop/Tail/Indicator Diffused Tail Function With Sequential Indicator - 520ARRMB
2019 Audi Q5 headlight-bulbs — are they used on this model?
Short answer: for Australian and New Zealand–delivered 2019 Audi Q5 (FY) models, traditional headlight bulbs aren’t used for the low or high beam. Audi’s own technical sources — the MY19 Audi Q5 AU/NZ specification sheets and the owner’s manual — specify LED headlights (with Matrix LED on higher variants) and note there are no user-replaceable “bulbs” in the headlamp units. Instead, the car uses sealed LED light modules with dedicated control electronics.
Why no bulbs? The Q5’s LED headlamps integrate the light source, optics, cooling and driver electronics into a single assembly. This design allows precise light distribution, better energy efficiency, and long service life. It also supports tech like automatic high-beam and adaptive light modes (on Matrix LED), which simply isn’t possible with old-school halogen bulbs and is more complex than conventional HID xenon setups.
What does this mean for servicing? If a headlight starts flickering, throws a warning, or fails, it’s not a case of popping in a new bulb. Diagnosis should be done with factory-level scan tools to check the LED control unit (driver), wiring and the headlamp module itself. Repairs typically involve replacing the control module or the entire headlamp assembly, then coding and aiming the unit to factory spec. The owner’s manual advises having this work carried out by a qualified workshop due to high-voltage components and the need for correct calibration.
- Care tips: keep the lenses clean with pH-neutral wash products, avoid abrasive compounds on the polycarbonate lens.
- Check headlight aim after suspension or load changes to maintain proper beam height.
- If condensation appears inside the lamp and doesn’t clear after a drive, get it inspected — the venting system or seals may need attention.
Heads-up on market differences: some overseas 2019 Q5 trims used HID xenon bulbs (e.g., D3S) — those do have replaceable bulbs. However, for AU/NZ-spec 2019 Q5s, “headlight-bulbs” listings aren’t relevant because the car uses integrated LED assemblies for both low and high beam.
- Does the 2019 Audi Q5 in Australia or New Zealand have replaceable headlight bulbs?
Generally, no. Local-spec 2019 Q5 models use LED or Matrix LED headlights with no user-replaceable bulbs for low or high beam. The modules are sealed and serviced as components rather than simple bulbs. - What should owners do if a 2019 Q5 LED headlight starts flickering or fails?
Book a diagnostic with a workshop familiar with Audi systems. They’ll scan for headlight control unit faults, check wiring and earths, and determine if the LED driver or the headlamp module needs replacement and coding. - Can individual LEDs be repaired, or does the whole headlamp need replacing?
Individual LED chips aren’t serviced separately. Depending on the fault, the LED control unit may be replaced, if the light source or optics are compromised, the complete headlamp assembly is typically replaced and then aimed and coded.