Your Selected Vehicle
Parts for your 2019 Audi Q5-Headlight bulbs
LED Autolamps 12/24V Front End Outline Marker Recessed Fitting Twin Blister - 7922WM2
LED Autolamps Multi Volt Stop/Tail/Indicator Lamp With Reflex Reflectors Grey Base Blister Pack 1 pce - 100ARM
LED Autolamps 174 Series Stop/Tail Lamp 12/24V, Surface Mount, 40cm Cable - 174RMB
LED Autolamps 174 Series Reverse Lamp 12/24V, Surface Mount, 40cm Cable - 174WMB
Explore 4WD & Adventure
LED Autolamps 174 Series Stop/Tail/Indicator Lamp 12/24V, Surface Mount, 40cm Cable - 174ARMB
LED Autolamps 10/30V LED Side Direction Indicator Light With 30cm Wire - 35AMB
LED Autolamps 12V Stop/Tail Lamp Black Chrome Round With Clear Lens - 102RBC
LED Autolamps 12/24V Round Stop/Tail Lamp With Clear Lens 130mm Diameter Recessed Mount Blister Pack - 102RCM
LED Autolamps Licence Plate Lamp Black Bracket Multi Volt With 1m Cable - 35BLM1P
LED Autolamps 12V 82 Series Stop/Tail/Indicator/Reverse Lamp Black Bracket - 82BARW
LED Autolamps 12/24V Reversing Lamp With 25 White LEDs With Bracket and 30cm Wire - 100WM
LED Autolamps Multi Volt Stop/Tail/Indicator With 18 Square LEDs Twin Blister - 135ARM/2
LED Autolamps 12V Front Indicator Amber Lens Black Base Twin Blister Pack - 175A/2
LED Autolamps 12/24V LED Reverse Lamp Screw Surface Mount Blister Pack - 12WM-2
LED Autolamps 12/24 Multi Volt Stop/Tail/Indicator/Reverse Assembly Lamp With 108 LEDs - 80BARWM
LED Autolamps LHS, Stop/Tail/SEQ-Indicator/Reverse/Reflector 12/24V 284 X 100 X 37mm, DT04 Connector - SO284LHS
2019 Audi Q5 headlight-bulbs — are they used on this model?
Short answer: for Australian and New Zealand–delivered 2019 Audi Q5 (FY) models, traditional headlight bulbs aren’t used for the low or high beam. Audi’s own technical sources — the MY19 Audi Q5 AU/NZ specification sheets and the owner’s manual — specify LED headlights (with Matrix LED on higher variants) and note there are no user-replaceable “bulbs” in the headlamp units. Instead, the car uses sealed LED light modules with dedicated control electronics.
Why no bulbs? The Q5’s LED headlamps integrate the light source, optics, cooling and driver electronics into a single assembly. This design allows precise light distribution, better energy efficiency, and long service life. It also supports tech like automatic high-beam and adaptive light modes (on Matrix LED), which simply isn’t possible with old-school halogen bulbs and is more complex than conventional HID xenon setups.
What does this mean for servicing? If a headlight starts flickering, throws a warning, or fails, it’s not a case of popping in a new bulb. Diagnosis should be done with factory-level scan tools to check the LED control unit (driver), wiring and the headlamp module itself. Repairs typically involve replacing the control module or the entire headlamp assembly, then coding and aiming the unit to factory spec. The owner’s manual advises having this work carried out by a qualified workshop due to high-voltage components and the need for correct calibration.
- Care tips: keep the lenses clean with pH-neutral wash products, avoid abrasive compounds on the polycarbonate lens.
- Check headlight aim after suspension or load changes to maintain proper beam height.
- If condensation appears inside the lamp and doesn’t clear after a drive, get it inspected — the venting system or seals may need attention.
Heads-up on market differences: some overseas 2019 Q5 trims used HID xenon bulbs (e.g., D3S) — those do have replaceable bulbs. However, for AU/NZ-spec 2019 Q5s, “headlight-bulbs” listings aren’t relevant because the car uses integrated LED assemblies for both low and high beam.
- Does the 2019 Audi Q5 in Australia or New Zealand have replaceable headlight bulbs?
Generally, no. Local-spec 2019 Q5 models use LED or Matrix LED headlights with no user-replaceable bulbs for low or high beam. The modules are sealed and serviced as components rather than simple bulbs. - What should owners do if a 2019 Q5 LED headlight starts flickering or fails?
Book a diagnostic with a workshop familiar with Audi systems. They’ll scan for headlight control unit faults, check wiring and earths, and determine if the LED driver or the headlamp module needs replacement and coding. - Can individual LEDs be repaired, or does the whole headlamp need replacing?
Individual LED chips aren’t serviced separately. Depending on the fault, the LED control unit may be replaced, if the light source or optics are compromised, the complete headlamp assembly is typically replaced and then aimed and coded.