Your Selected Vehicle
Parts for your 2014 Audi Q5-Batteries
LED Autolamps Front Marker LED White With Reflector 12-24V Perm Mnt - EU38WMHD
Explore 4WD & Adventure
LED Autolamps 10/30V Front Outline Position Marker 4 White LEDs With 40cm Wire - 35WM
LED Autolamps 12V Stop/Tail/Indicator/Reverse Assembly Chrome Bracket Blister Pack - 82CARRW
LED Autolamps Front End Outline Marker White 12/24Vwith 2P plugs 10cm cable - 58WMB2P
LED Autolamps 12/24V Round Indicator Lamp With Clear Lens 130mm Diameter Recessed Mount - 102ACM
LED Autolamps MultiVolt R.H.S Stop/Tail/Indicator Assembly 128 Round LEDs - 125BARMR
LED Autolamps Twin function side indicator with amber/red side marker - 97ARIMB
LED Autolamps 12V LED Stop/Tail/Indicator/Reverse Assemnly Lamp With 108 LEDs - 80BARW
LED Autolamps Twin function rear position with supplementary rear indicator - 97RIMB
LED Autolamps 12/24V Stop/Tail/Indicator/Reverse Assembly With 123 LEDs - 100BARWM
LED Autolamps Multi Volt LED Licence Plate Lamp With Chrome Base Twin Blister - 30CLM
LED Autolamps RHS, Stop/Tail/SEQ-Indicator/Reverse/Reflector 12/24V 284 X 100 X 37mm, DT04 Connector - SO284RHS
LED Autolamps 12/24V Stop/Tail/Indicator/Reverse Assembly 3 Lamps With 153 LEDs - 125BARWM
LED Autolamps 12/24V LED Stop/Tail/Indicator Light 284x100x27mm Blister Pack - 282ARRM
LED Autolamps Twin function rear position with supplementary rear indicator - 97CRIM
LED Autolamps Twin function front position with supplementary front indicator - 97WIM
2014 Audi Q5 Batteries – What They Do and How to Look After Them
Based on technical references including the 2014 Audi Q5 Owner’s Manual (electrical system and vehicle battery sections), Audi’s workshop procedures (battery energy management and start/stop requirements), and major fitment guides from Bosch and Exide, the 2014 Audi Q5 absolutely uses a 12‑volt battery. Most variants are factory-fitted with an AGM (Absorbent Glass Mat) unit to support start/stop and the vehicle’s battery energy management system.
In this Q5 (Typ 8R), the battery sits in the boot under the floor. Its job is more than just cranking the engine: it stabilises the electrical system for safety tech, infotainment, lighting, and stop/start functionality. Audi’s energy management monitors state of charge via an intelligent sensor on the negative terminal, and adjusts charging to protect the battery and keep systems happy.
As part of regular servicing, the battery deserves a quick health check. For vehicles with start/stop, an AGM battery of the correct capacity (commonly around 80–95Ah, H7/LN4 size) should be used. Swapping to a cheaper flooded battery can upset start/stop and shorten service life. After replacement, the Q5 expects the new battery to be “registered” or adapted in the control unit so charging strategy matches the battery’s type, capacity, and age. Audi dealers do this via ODIS, independent workshops can use appropriate diagnostic tools.
- Signs it’s time: slow cranking, frequent start/stop deactivation, warning messages, or interior lights dimming at idle.
- Helpful habits: regular longer drives to allow full charge, avoid leaving accessories on with the engine off, and keep terminals clean and snug.
- Replacement tips: maintain vehicle memory with a support power supply, choose an AGM of the correct spec, and have the battery coded/registered after install.
Jump-starting and charger connection should use the proper positive post and the recommended chassis earth rather than the battery’s negative post, protecting the current sensor. A smart charger with an AGM mode is best if the Q5 sits for weeks at a time. With the right battery and a bit of care, owners can expect strong cranking, reliable start/stop, and fewer electrical gremlins.
- What battery type and size suits a 2014 Audi Q5?
Most 2014 Q5 models use an AGM 12‑volt battery, commonly H7/LN4 size around 80–95Ah. Start/stop cars should stay with AGM to handle higher cycling and meet Audi’s charging strategy. - Does the battery need coding after replacement?
Yes. Audi’s battery energy management expects the new battery details (type, Ah rating, manufacturer/serial). Registering/coding ensures correct charging and accurate state‑of‑charge readings. - Where is the battery and can a home mechanic replace it?
It’s in the boot under the floor. A competent DIYer can swap it, but having the correct support power, using an AGM unit, and performing the post‑fitment registration with a scan tool are key steps.