Your Selected Vehicle
Parts for your 2014 Audi Q5-Batteries
Narva Model 63 Front End Outline Marker, Side Indicator (Amber) Or External Cabin Marker Lamp Black Base And 0.5M Cable
Narva Model 70 Rear Stop/Tail/Indicator/Reverse Lamp With In-Built Retro Reflector, With 0.5M Of Cable, Bulk Pack Of 4 - 97010-1/4
Explore 4WD & Adventure
Narva 9-33 Volt Surface Mount LED Side marker lamp(red/amber) with Chrome cover and 0.5m cable - 96802
Narva MDL38 Stop/Tail/Indicator Red-Amber Lens LED 10 to 30V - 2 Pce - 93812BL2
Narva Model 70 Rear Stop/Tail /Indicator Lamp With In-Built Retro Reflector, With 0.5M Of Cable And Dt Plug - 97000-1-D
Narva Model 70 Rear Stop/Tail/Indicator/Reverse Lamp With In-Built Retro Reflector, With 0.5M Of Cable And Dt Plug - 97010-1-D
Narva 9-33 Volt Surface Mount LED Side directional indicator(amber) with Black cover and 0.5m cable - 96842B
Narva 9-33 Volt LED Rear Stop/Tail and direcion indicator and reverse lamp with in built retro reflector and 0.5m hard wired cable - 97310
Narva 9-33 Volt LED Rear Stop/Tail, Left Hand Squential direcion indicator and reverse lamps with in built retro reflector and 0.5m hard wired cable - 97312L
2014 Audi Q5 Batteries – What They Do and How to Look After Them
Based on technical references including the 2014 Audi Q5 Owner’s Manual (electrical system and vehicle battery sections), Audi’s workshop procedures (battery energy management and start/stop requirements), and major fitment guides from Bosch and Exide, the 2014 Audi Q5 absolutely uses a 12‑volt battery. Most variants are factory-fitted with an AGM (Absorbent Glass Mat) unit to support start/stop and the vehicle’s battery energy management system.
In this Q5 (Typ 8R), the battery sits in the boot under the floor. Its job is more than just cranking the engine: it stabilises the electrical system for safety tech, infotainment, lighting, and stop/start functionality. Audi’s energy management monitors state of charge via an intelligent sensor on the negative terminal, and adjusts charging to protect the battery and keep systems happy.
As part of regular servicing, the battery deserves a quick health check. For vehicles with start/stop, an AGM battery of the correct capacity (commonly around 80–95Ah, H7/LN4 size) should be used. Swapping to a cheaper flooded battery can upset start/stop and shorten service life. After replacement, the Q5 expects the new battery to be “registered” or adapted in the control unit so charging strategy matches the battery’s type, capacity, and age. Audi dealers do this via ODIS, independent workshops can use appropriate diagnostic tools.
- Signs it’s time: slow cranking, frequent start/stop deactivation, warning messages, or interior lights dimming at idle.
- Helpful habits: regular longer drives to allow full charge, avoid leaving accessories on with the engine off, and keep terminals clean and snug.
- Replacement tips: maintain vehicle memory with a support power supply, choose an AGM of the correct spec, and have the battery coded/registered after install.
Jump-starting and charger connection should use the proper positive post and the recommended chassis earth rather than the battery’s negative post, protecting the current sensor. A smart charger with an AGM mode is best if the Q5 sits for weeks at a time. With the right battery and a bit of care, owners can expect strong cranking, reliable start/stop, and fewer electrical gremlins.
- What battery type and size suits a 2014 Audi Q5?
Most 2014 Q5 models use an AGM 12‑volt battery, commonly H7/LN4 size around 80–95Ah. Start/stop cars should stay with AGM to handle higher cycling and meet Audi’s charging strategy. - Does the battery need coding after replacement?
Yes. Audi’s battery energy management expects the new battery details (type, Ah rating, manufacturer/serial). Registering/coding ensures correct charging and accurate state‑of‑charge readings. - Where is the battery and can a home mechanic replace it?
It’s in the boot under the floor. A competent DIYer can swap it, but having the correct support power, using an AGM unit, and performing the post‑fitment registration with a scan tool are key steps.