Your Selected Vehicle
Parts for your 2012 Subaru Tribeca-Harmonic balancers
Champion High Tensile Hex Set Screws and Nuts – 1/4in x 3/4in UNF – Grade 5 - BF3
Champion High Tensile Flanged Hex Set Screws & Nuts – M8 x 16mm (12AF) Grade 8.8 - FBM45
Champion High Tensile Hex Set Screws and Nuts – M10 x 45mm x 1.25 Pitch – Grade 8.8 - BM109
Champion High Tensile Flanged Hex Set Screws & Nuts – M6 x 30mm (10AF) Grade 8.8 - FBM25
Champion Nickel Plated Pan Slot Machine Screws & Nuts – 8/36in x 1-1/4in - BH082
Champion High Tensile Hex Set Screws & Nuts – M12 x 35 x 1.25mm Grade 8.8 - BM150
Champion High Tensile Hex Set Screws and Nuts – 5/16in x 3/4in UNC – Grade 5 - BC15
Champion High Tensile Hex Set Screws and Nuts – 5/16in x 1-1/4in UNC – Grade 5 - BC19
Champion High Tensile Hex Set Screws and Nuts – M10 x 35mm x 1.25 Pitch – Grade 8.8 - BM106
Champion High Tensile Flanged Hex Set Screws & Nuts – M6 x 25mm (10AF) Grade 8.8 - FBM23
Champion High Tensile Hex Set Screws & Nuts – M10 x 35 x 1.00mm Grade 8.8 - BM102
Champion High Tensile Hex Set Screws & Nuts – 3/8in x 1-1/2in UNC Grade 5 - BC36
Champion High Tensile Hex Set Screws & Nuts – 3/8in x 1in UNC Grade 5 - BC33
Champion High Tensile Hex Set Screws and Nuts – M10 x 25mm x 1.25 Pitch – Grade 8.8 - BM104
Champion SEMS Hex Set Screws with Combo Drive, Flat & Spring Washer Pilot – M6 x 20mm - TF250
Champion High Tensile Hex Set Screws & Nuts – 3/8in x 3/4in UNC Grade 5 - BC31
2012 Subaru Tribeca harmonic balancers: what they do and when to replace
Based on the Subaru 2012 Tribeca Factory Service Manual (Engine Mechanical – Crankshaft Pulley), the Subaru FAST parts catalogue, and aftermarket catalogues from major suppliers that list a damper/crank pulley for the EZ36D 3.6‑litre engine, the 2012 Subaru Tribeca is fitted with a harmonic balancer. It’s integrated into the crankshaft pulley with a bonded rubber layer that dampens torsional vibration.
On this Tribeca’s flat‑six, the harmonic balancer’s job is to smooth out crankshaft twist as each cylinder fires. By absorbing those pulses, it protects the timing gear, chains, bearings and accessory drive from copping unnecessary vibration. It also keeps the serpentine belt tracking sweet, so the alternator, power steering and A/C behave themselves under load.
It’s not a scheduled replacement item in the service book, but it does deserve regular eyes‑on checks. A good routine is to inspect it at each service interval (around 10,000–15,000 km). Under the bonnet, look for perished or oil‑soaked rubber between the inner hub and outer ring, any wobble at idle, or the belt walking on the pulley. If there’s slinging rubber dust or a faint chirp that comes and goes with revs, that’s a red flag too.
When replacement’s due, go for a quality OE or reputable aftermarket unit matched to the EZ36D. It’s smart practice to fit a fresh drive belt at the same time and check the tensioner and idlers while you’re in there. The crank bolt needs the correct torque and angle as per the factory manual, and a proper pulley holding tool makes the job far less of a wrestle. If there’s been an oil leak at the front of the engine, sort that out first — oil degrades the damper’s rubber and will shorten the new balancer’s life.
Left too long, a failed balancer can cause nasty vibrations, poor charging, misaligned belts and even damage to the crank over time. Catching issues early keeps the Tribeca feeling smooth and quiet — the way a big Subaru six should.
- Common symptoms: wobble at idle, chirping/squealing belt, visible rubber cracking/delamination, vibration through the cabin, intermittent A/C or charging issues.
- Service tip: inspect every service, replace at the first sign of deterioration, and keep oil leaks off the pulley.
Popular questions
Does a 2012 Subaru Tribeca have a harmonic balancer?
Yes. The EZ36D 3.6‑litre flat‑six uses a crankshaft pulley with an integrated rubber damper. Subaru service literature and parts catalogues list it as the crank pulley/damper for this model.
What are the signs the balancer is failing on a Tribeca?
Owners might notice a wobbly crank pulley at idle, a chirp or squeal that follows engine speed, the serpentine belt walking off line, or extra vibration under load. Cracked or oil‑soaked rubber in the pulley is a giveaway. If any of these pop up, it’s time for a proper inspection.
Should it be replaced with the drive belt?
It doesn’t need changing as often as the belt, but if the balancer shows wear, replace it and fit a fresh belt at the same time. It’s also a good moment to check the tensioner and idlers, so the new parts aren’t fighting tired neighbours.