Your Selected Vehicle
Parts for your 2008 Toyota Land cruiser-Headlights
Narva Model 72 Rear Stop/Tail/Indicator/Reverse Lamp With In-Built Retro Reflector, With 0.5M Of Cable
OEX 6mm Twin Core Automotive Cable, Red/Black, With Black Sheath - 5m Blister Pack (NZ Ref. 157) - ACX0811-5BL
Narva Battery Master / Isolation Switch Plastic With Removable Key (Contacts Rated 100A at 12V) - 61038BL
LED Autolamps LED Autolamps Front Indicator/Position LED Light Clear Lens 12v Twin Blister Pack - 175AW/2
OEX Crimp Terminal Female Blade Brass Terminal Entry 6.3 x 0.8mm Non Insulated 100 Pce - ACX3078
OEX Crimp Terminal Female Blade Blue Terminal Entry 6.3 x 0.8mm Heat Shrinkable 50 Pce - ACX3168
OEX Rocker Surface Mount Switch On/Off SPST 12V Blue Illuminated (contacts Rated 30A @ 12V) - ACX1973BL
2008 Toyota Land Cruiser Headlights
Headlights are absolutely relevant and factory‑fitted on the 2008 Toyota Land Cruiser (200 Series). Toyota’s 2008 Land Cruiser Owner’s Manual and the Toyota 200 Series Repair Manual cover headlamp operation and service, and Australian Design Rule (ADR) 13/00 along with New Zealand’s Land Transport Rule: Vehicle Lighting 2004 legally require compliant headlamps on vehicles. So yes—this Land Cruiser uses headlights, and they’re a core safety system.
On this model, the headlights are there to light the way on dark country roads, help the driver be seen in poor weather, and provide the right beam pattern so oncoming traffic isn’t dazzled. Low beam handles everyday driving, while high beam throws a longer pattern for open‑road visibility. Many AU/NZ 2008 Land Cruisers run halogen globes, while higher‑spec trims (like Sahara) may be fitted with factory HID xenon low beams and auto‑levelling.
- Common fitments: H11 low beam and HB3/9005 high beam (halogen), Sahara variants often use D4S xenon low beam. Fog lamps are typically H11. Always confirm by checking the owner’s manual or the marking on the lamp housing.
As part of regular servicing, it’s smart to give the headlights a once‑over. Dim output, colour shift, or flicker are cues a globe is on the way out. Replacing in pairs keeps brightness even. For halogen, avoid touching the glass—oils shorten life. For HID xenon, remember there’s high voltage involved, disconnect the battery, allow time for discharge, and if in doubt, hand it to a qualified tech.
- Keep lenses clean and clear. If they’re going yellow or hazy, a quality restore kit plus a UV‑stable clear coat brings back output.
- Check aim after bulb or suspension work. Use the in‑cabin levelling dial (if fitted) and have a workshop set aim to ADR/NZ specs for a roadworthy/WOF.
- Inspect dust caps, seals, and vents. Persistent condensation points to a seal issue—dry the unit, replace seals, and ensure vents aren’t blocked.
- If considering LED upgrades, choose ADR/ECE‑approved complete lamp assemblies. Drop‑in LED bulbs in halogen housings are often not legal and can glare other drivers.
- During services (about every 10,000–15,000 kilometres), check globes, fuses, connectors, and the headlight relay to stay ahead of night‑time surprises.
Look after the headlights on a 2008 Land Cruiser and they’ll repay the favour with confident visibility from the paddock to the motorway.
What bulb type fits a 2008 Land Cruiser?
Most AU/NZ 2008 200‑Series use H11 for low beam and HB3/9005 for high beam. Higher‑grade models like the Sahara often have D4S HID xenon low beams with auto‑levelling and washers. Always verify against the vehicle’s manual and the markings on the lamp housing.
Are LED headlight upgrades legal in Australia and New Zealand?
Many drop‑in LED bulbs fitted into halogen housings aren’t road‑legal because they don’t meet ADR/NZ beam and glare requirements. To stay compliant for roadworthy/WOF, use ADR/ECE‑approved lamps or complete headlight assemblies designed for LED.
Why are my headlights cloudy or fogging up?
UV exposure causes lens haze, a restore and UV clear coat can revive them. Light condensation can be normal, but standing water or persistent fogging usually means a sealing or venting issue—inspect dust caps and seals and replace any that are perished.