Your Selected Vehicle
Parts for your 2007 Nissan Pathfinder-Headlight bulbs
LED Autolamps 24V Front Direction Indicator With Front Position Lamp Chrome Bracket - 200CAW/24
LED Autolamps Front Marker LED White With Reflector 12-24V Perm Mnt - EU38WMHD
LED Autolamps 174 Series Reverse Lamp 12/24V, Surface Mount, 40cm Cable - 174WMB
Explore 4WD & Adventure
LED Autolamps 174 Series Stop/Tail/Indicator Lamp 12/24V, Surface Mount, 40cm Cable - 174ARMB
LED Autolamps Tray Conversion Kit To suits Hilux Contains Two Cables - PATCH-HILUX
LED Autolamps Multi Volt Stop/Tail Lamp With Rubber Grommet And Plug - 164RM
LED Autolamps 12/24 Multi Volt Stop/Tail Lamp 36 LEDs With 40cm Wire - 80RM
LED Autolamps 12/24V Round Stop/Tail Lamp With Clear Lens 130mm Diameter Recessed Mount Blister Pack - 102RCM
LED Autolamps 12V Stop/Tail/Indicator/Licence Plate Lamp With Reflector - 149BARL4P
LED Autolamps 12V Stop/Tail/Indicator Lamp Reflector With 4 Pin Plug - 149BAR4P
LED Autolamps Twin function rear position with supplementary rear indicator - 97RIM
LED Autolamps Licence Plate Lamp Black Bracket Multi Volt With 1m Cable - 35BLM1P
LED Autolamps 12V 82 Series Stop/Tail/Indicator/Reverse Lamp Black Bracket - 82BARW
LED Autolamps 12V/24V Round LED Stop/Tail Lamp With Grommet and Plug - 110RMG
2007 Nissan Pathfinder headlight bulbs
Based on technical sources – the 2007 Nissan Pathfinder Owner’s Manual (Lights), the Nissan R51 Factory Service Manual (LT: Lighting System), and ADR 13/00 rules for lamp fitment – this model uses replaceable halogen headlight bulbs. So yes, headlight bulbs are relevant and fitted to the 2007 Pathfinder.
On this Pathfinder, the headlight bulbs do the heavy lifting for safe night-time and poor-weather driving, throwing a clear beam that meets ADR requirements while keeping glare down for oncoming traffic. They’re a wear item: halogen capsules slowly dim and shift colour over time, even before they blow, so brightness can taper off without being obvious.
Bulb type varies by market and trim. Many 2007 Pathfinders run a dual‑filament halogen (commonly H13/9008, some builds use HB5/9007). Always confirm against the owner’s manual, the bulb base stamp, or a VIN‑matched parts catalogue. Stick to the specified wattage (typically around 55/60–65 W) to avoid overheating the wiring and lamp housings.
- Tell-tales it’s time: noticeably dimmer output, a yellowish beam, flickering, or one side out.
- Best practice: replace in pairs so left and right match in colour and brightness.
- Service rhythm: many drivers refresh halogens every 3–5 years or ~60,000–100,000 km, depending on night driving and DRL usage.
Under the bonnet, access is from behind the headlamp. Disconnect the battery negative if space is tight, unclip the dust cover, unplug the connector, then twist the bulb anti‑clockwise. Refitting is the reverse. Don’t touch the glass, skin oils create hot spots that shorten bulb life. Use clean gloves or a tissue if needed. Check the rubber boot seals well to keep moisture out, and give the headlamp lens a quick clean inside and out if there’s safe access.
After any bulb change, check headlamp aim on a flat surface at night. If the beam looks off, adjust the headlamp aiming screws as outlined in the FSM so the cut-off sits correctly and doesn’t dazzle other road users. If a new bulb doesn’t light, inspect the relevant fuse, relay, and earth points before assuming the bulb is faulty.
- Confirm bulb type and wattage.
- Work with the ignition off, disconnect negative if needed.
- Remove dust cap, unplug, and twist out old bulb.
- Fit new bulb without touching glass.
- Refit cap and connector, test lights.
- Check aim and beam pattern.
Popular questions
What headlight bulb type fits a 2007 Nissan Pathfinder?
Most 2007 Pathfinders use a dual‑filament halogen such as H13/9008, though some markets/builds use HB5/9007. Because there were regional differences, it’s smart to confirm via the owner’s manual, the stamp on the old bulb, or a VIN‑matched parts lookup so the base and wattage are spot on.
Should both headlight bulbs be replaced at the same time?
Yes. Halogen bulbs dim with age, so replacing both keeps the colour and brightness matched. It also saves time, avoids uneven illumination, and helps maintain a correct, balanced beam pattern when the lamps are re‑aimed after fitting.
Why avoid touching the glass on a new bulb?
Skin oils leave residue that causes a hot spot on the quartz when the bulb heats up, which can lead to early failure or a cloudy bulb. Handle the metal base only, or use clean gloves or tissue. If you do touch the glass, wipe it with isopropyl alcohol and let it dry before installation.