Your Selected Vehicle
Parts for your 2001 Daihatsu Gran move-Headlights
LED Autolamps 12V Blue Courtesy Lamp Super Small Design Twin Blister Pack - 16B12-2
Explore 4WD & Adventure
LED Autolamps 275GARWM + 2 X LR12 + 450mm Loom DT04 Connector And 500mm LP Cable - SO275GARWM2LR450
LED Autolamps 12V Stop/Tail/Indicator/Reverse With Reflectors And 500mm LP Cable - SO283ARWM2LR12
LED Autolamps 12/24 Multi Volt Stop/Tail/Indicator/Reverse Assembly Lamp With 108 LEDs - 80BARWM
LED Autolamps 12/2V Maxilamp LED Stop/Tail/Indicator/Reflector Black Chrome Bolt Mount - MAXILAMPC1XCE
LED Autolamps 12V 82 Series Stop/Tail/Indicator/Reverse Lamp Black Bracket - 82BARW
LED Autolamps 12/24V Reverse Lamp Horizontal/Vertical Mount Twin Blister - 11WM-2
LED Autolamps Multi Volt Stop/Tail/Indicator Lamp 190x95x28mm Blister Pack - 280ARM
LED Autolamps Traffic Advisory Light Red LED 12v Only Red Lens 10cm Cable Boxed - 83R
LED Autolamps 174 Series Rear Indicator Lamp 12/24V, Surface Mount, 40cm Cable - 174AMB
LED Autolamps Multi Volt Round Indicator Lamp With Amber Lens Recessed Mount - 102AM
2001 Daihatsu Gran Move Headlights — Purpose, Care and Replacement
Headlights are absolutely fitted to the 2001 Daihatsu Gran Move and are essential for road use. This is supported by the Daihatsu Gran Move/Pyzar owner’s manual and parts catalogues for the late-1990s to early-2000s models, which list front headlamp assemblies and halogen bulbs. Road rules in Australia and New Zealand also require compliant headlamps on passenger vehicles, aligning with UN ECE lighting regulations for installation and performance.
On the Gran Move, the headlights provide safe forward visibility at night and in poor weather while ensuring the car is seen by others. Most examples use a dual‑filament H4 60/55 W halogen bulb for high and low beam in a single reflector unit, with a separate small wedge bulb for the park light. Always confirm bulb types in the owner’s manual or against the existing lamp.
As part of regular servicing, it pays to give the Gran Move’s headlights a quick once‑over. Check for dimming, flicker, moisture inside the lens, yellowing of the plastic, damaged connectors, and blown fuses. Replace bulbs in pairs to keep the beam colour and brightness consistent left to right. If the lenses are hazy, a reputable headlight restoration kit can restore clarity and improve beam performance.
Basic bulb swap steps (typical H4 setup):
- Open the bonnet and locate the rear of the headlamp. Disconnect the three‑pin H4 plug.
- Peel off the rubber dust cap.
- Unclip the spring retainer and withdraw the bulb.
- Install the new bulb without touching the glass, refit the clip and dust cap, then reconnect the plug.
Handy tips:
- Never touch the glass of a halogen bulb, oils can cause hot spots and early failure.
- Stick to the correct wattage to avoid wiring and reflector damage.
- Inspect headlight aim after any bulb or front‑end work. Mis‑aimed lights can fail a WOF (NZ) or RWC (AU) and reduce night vision.
- If you spot condensation, check the rear cap seal and vent, minor fogging after rain can be normal, persistent moisture is not.
- A dab of dielectric grease on connectors can help ward off corrosion, especially on older looms.
A quick headlight check at each service interval (around 10,000 km or six months) keeps the Gran Move shining bright and legal on Aussie and Kiwi roads.
Popular questions about 2001 Daihatsu Gran Move headlights
What headlight bulbs does a 2001 Gran Move use?
Most 2001 Gran Move models use an H4 60/55 W halogen for high/low beam and a T10 wedge for the park light. Variations can exist by market and trim, so it’s smart to verify against the existing bulb or the owner’s manual.
How often should headlight bulbs be replaced?
There’s no strict interval, replace on failure or noticeable dimming. Check operation and lens condition at each service. Replace in pairs to keep beam colour and brightness matched.
How do you adjust the headlight aim?
Use the adjuster screws on the back of each headlamp. Park on level ground facing a wall or aiming screen and follow a standard ECE/ADR pattern. If you’re unsure, a workshop can set the aim correctly to meet WOF/RWC standards.