Your Selected Vehicle
Parts for your 1998 Suzuki Swift-Headlight bulbs
Repco by Century Car Battery Superior Performance 500CCA - 55D23L MF
Repco by Century Car Battery 4x4 & SUV Ultimate Performance 760CCA - N70ZZLX MF
Repco by Century Car Battery Ultimate Performance 550CCA - 75D23L MF
Repco by Century Car Battery Ultimate Performance 710CCA - DIN65LHX MF
Explore 4WD & Adventure
Repco by Century Car Battery Superior Performance 400CCA - NS60L MF
Repco by Century Car Battery Ultimate Performance 600CCA - DIN53LHX MF
Repco by Century Car Battery Ultimate Performance 550CCA - 75D23R MF
Repco by Century 4x4 & SUV Battery Ultimate Performance 680CCA - NS70LX MF
Repco by Century Car Battery 4x4 & SUV Superior Performance 680CCA - N70ZZ MF
Repco by Century Car Battery Ultimate Performance 640CCA - DIN65LX MF
Repco by Century Car Battery Ultimate Performance 860CCA - DIN85LHX MF
Repco H11 Headlight Bulb Plus 30 Performance 12V 55W Pgj192 Bl - RH11BL-2
1998 Suzuki Swift headlight-bulbs — what they do and how to look after them
Headlight-bulbs are absolutely relevant to the 1998 Suzuki Swift. Technical references including the 1998 Suzuki Swift (SF series) owner’s manual and the Suzuki Genuine Parts catalogue specify a replaceable H4 12V 60/55W halogen bulb for the headlamps. Industry bulb guides from major lighting manufacturers also list H4 for this model across AU/NZ variants, confirming it’s a standard halogen reflector setup rather than a sealed-beam or HID unit.
On a ’98 Swift, the headlight-bulbs provide both low and high beam via a dual‑filament H4, giving clear forward vision at night and helping oncoming traffic see the car. Because halogen output fades with age, even before a filament blows, keeping bulbs fresh is a simple way to boost safety and stay compliant with local roadworthy/WOF checks.
For servicing, it’s smart to replace headlight-bulbs in pairs so beam colour and brightness match. Stick with 12V 60/55W H4 to avoid cooking wiring or reflectors, higher‑wattage bulbs can overheat and may not be legal without upgraded looms and relays. If extra punch is needed, choose ADR/ECE‑approved “plus” performance H4s rather than upping wattage.
Typical replacement steps are straightforward: unplug the three‑pin connector at the rear of the lamp, peel back the rubber boot, release the spring clip, remove the old H4, and seat the new bulb with the locating tab correctly oriented. Avoid touching the glass, fingerprints can create hot spots and shorten life. Reseat the clip, refit the boot, and reconnect the plug, then test both beams.
During a service, it’s worth checking aim and lens condition. Cloudy lenses or moisture inside the housing will dull output, polish the lens if it’s hazed and sort any seal leaks. If a new bulb doesn’t light, check the fuse, relay, and earth connections at the headlamp. Many owners do a quick headlight check every few months or before long night drives.
- Bulb spec: H4 (HB2/9003 equivalent), 12V 60/55W halogen
- Replace in pairs for even light and colour
- Don’t touch the glass, use gloves or a clean tissue
- Verify beam aim after any bulb change
FAQs
What bulb type fits a 1998 Suzuki Swift?
Most AU/NZ 1998 Swifts take an H4 12V 60/55W halogen bulb for both low and high beam. Trim levels and aftermarket headlamp assemblies can vary, so it’s wise to check the stamping on the headlamp or the owner’s manual before buying. Avoid higher‑wattage bulbs unless the wiring has been upgraded and the setup remains road‑legal.
How do you change the headlight-bulb on a ’98 Swift?
Open the bonnet, unplug the 3‑pin connector from the back of the headlamp, peel off the rubber dust boot, then unclip the spring retainer. Swap in the new H4 (don’t touch the glass), refit the clip and boot, reconnect the plug, and test low/high beam. If the beam pattern looks off, adjust the aim using the headlamp adjusters.
Should headlight-bulbs be replaced in pairs?
Yes, it’s recommended. Halogen bulbs dim over time, so a single fresh bulb can look brighter and a different colour to the older side. Replacing both keeps light output even and avoids one side failing soon after the other.