Your Selected Vehicle
Parts for your 1998 Mitsubishi Pajero-Headlights
LED Autolamps 12V Black Chrome Round Indicator Lamp With Clear Lens - 102ABC
LED Autolamps 355 Series Multi Volt Black Stop/Tail/Indicator/Reverse/Reflector LHS & RHS Twin Blister Pack - 355BARWM-2
LED Autolamps 12V Sequential Indicator Strip Light 10 Square LEDS Amber Lens Blister Pack - 235ASEQ-2
LED Autolamps 12/24V 280 Mini Jumbo Stop/Tail/Indicator Lamp Blister Pack - 280ARRM
LED Autolamps Twin function side indicator with amber side marker - 97CAIMCSB
Explore 4WD & Adventure
LED Autolamps 385 Series Rear Combination Lamp LHS with 7 core plug - 385ARWMLCSB
LED Autolamps 12V Stop/Tail/Ind/Rev LED Light Kit 450mm Loom DT04 Connector - SO282ARWM2LR450
LED Autolamps 12V Sequential Indicator Strip Light 10 Square LEDS Amber Lens Bulk Packaging - 235ASEQB
LED Autolamps 12/24V LED Stop/Tail/Indicator/Reflector Light 28cm Cable Blister Pack - 275MAR
LED Autolamps Multi Volt Round Indicator Lamp With Amber Lens Recessed Mount - 102AM
LED Autolamps 12/24V Stop/Tail/Indicator/Reflector With Licence Plate Lamp - 99ARLM
LED Autolamps 12V Front Indicator/Marker Lamp 80mm Round Blister Pack - 80AW
LED Autolamps 174 Series Rear Indicator Lamp 12/24V, Surface Mount, 40cm Cable - 174AMB
LED Autolamps 12/24V LED Stop/Tail/Indicator Lamp With Reflex Reflector Blister Pack 1 pce - 150ARM
LED Autolamps 10/30V LED Side Direction Indicator Light With 3m Tinned Cable - 58AM3
LED Autolamps 12/24V Stop/Tail/Indicator/Reverse Lamp With Inbuild Reflectors - 283ARWM
LED Autolamps 12V LED Stop/Tail/Indicator Assembly Light With Black Bracket - 80BAR
OEX Black Nylon Cable Ties - 4.8mm x 200mm, with Mounting Hole - 100 Pc - ACX1318
LED Autolamps Multi Volt Reverse Lamp With 35 SMDS Blister Pack With Black Base - 135WM
LED Autolamps Multi Volt Stop/Tail/Indicator Assembly 72 LEDs With Black Bracket - 200BARM
LED Autolamps 12V LED Stop/Tail/Indicator Light With Reflex Reflector Twin Blister - 100BAR2
LED Autolamps Front Indicator & Position Light LED 24V Surface Mount - 135CAT124
1998 Mitsubishi Pajero Headlights
Headlights are absolutely fitted to and required on the 1998 Mitsubishi Pajero. Technical references including the 1998 Pajero Owner’s Manual, the Mitsubishi workshop/service manual for the NL-series, and Australian/New Zealand regulatory standards (ADR 13/00 for lighting installation and ADR 46/00 for headlamps) all specify dipped and main-beam headlamps for this model. Most AU/NZ vehicles of this year use halogen reflector units, commonly with H4 60/55W bulbs—owners should confirm the exact bulb type in the handbook or on the lamp housing.
On a 1998 Pajero, the headlights do the core job of lighting up the road ahead and making the vehicle visible to others—crucial on country highways, unlit tracks, and changeable Kiwi and Aussie weather. Keeping them bright and correctly aimed isn’t just about compliance, it’s about safer night driving and better confidence behind the wheel.
For routine servicing, it’s worth checking the lenses for clouding or yellowing. The Pajero’s polycarbonate lenses can haze with UV exposure, a decent restoration kit and a UV sealant can bring them back, but if the coating is gone or cracks are present, replacing the assemblies is smarter. Inspect the rubber boots, connectors, and earth points under the bonnet for moisture or corrosion. A light smear of dielectric grease on terminals helps prevent gremlins. If a bulb pops, replace both sides together to keep brightness and colour matched.
Owners who’ve added a lift, a bull bar, or carry heavy loads should re-aim the beams. Tiny turns on the adjusters make a big difference—aim low beam so the cut-off sits just below the lamp centreline on a flat wall from several metres back. Avoid fitting higher-wattage or non-compliant LED/HID retrofits into halogen reflectors, they can dazzle others and won’t meet ADR requirements unless specifically approved for that housing.
Replacement is straightforward on most trims: pop the bonnet, unplug the connector, peel back the rubber boot, unclip the spring retainer, swap the bulb, and refit in reverse. Don’t touch the glass—use gloves. If both lights are out, check the fuses and headlight relay, if they’re fine, a stalk switch or ground fault may be the culprit. Finally, confirm charging voltage is in the 13.8–14.4V range so bulbs aren’t overcooked.
- Inspect lenses and aim at every service or 10,000 km.
- Use the specified bulb type and wattage, replace in pairs.
- Seal/replace perished boots and clean earths to prevent flicker.
What bulb type fits a 1998 Mitsubishi Pajero?
Most AU/NZ 1998 Pajeros run H4 60/55W halogen bulbs in reflector housings. Variations exist by trim and market, so it’s best to check the owner’s manual or the marking on the lamp. Sticking to the specified wattage avoids heat damage and stays compliant.
While LED or HID upgrades are tempting, retrofitting them into halogen reflector housings generally isn’t ADR-compliant and can cause glare. If keen on upgrades, look for E-marked/ADR-compliant complete assemblies or quality halogen +30/+50 bulbs.
How can cloudy or yellowed headlights be fixed?
Light to moderate haze usually responds well to a headlight restoration kit: sand (as directed), polish, then apply a UV sealant. This restores clarity and helps the fix last. If the lens is crazed, cracked, or the internal reflector is dull, replacement assemblies are the better call.
Also check for moisture inside the lamp. Replace torn boots and seals, and dry the housing before reassembly to stop the haze from returning.
How does one adjust the beam aim after a lift or load change?
Park on level ground several metres from a wall, with normal tyre pressures and fuel. Mark the headlamp centres on the wall, then use the adjusters so the low-beam cut-off sits slightly below and just to the left of those marks (for RHD markets). Small turns go a long way—aim for a crisp cut-off without stray glare.
If unsure, a workshop can align them quickly with a beam setter to ADR guidance, especially handy after suspension mods or if towing often.