Your Selected Vehicle
Parts for your 1993 Nissan Primera-Headlights
LED Autolamps 10/30V LED Side Direction Indicator Light With 3m Tinned Cable - 58AM3
LED Autolamps 12/24V Stop/Tail/Indicator/Reverse Assembly 3 Lamps With 153 LEDs - 125BARWM
LED Autolamps 12/24V Stop/Tail/Indicator/Reverse Lamp With Inbuild Reflectors - 283ARWM
Explore 4WD & Adventure
LED Autolamps 12V Interior Strip Light With Touch Sensor Switch With MCU Circuitry - 40410MCU
LED Autolamps 12V Stop/Tail/Indicator Lamp With Reflex Reflector 100x100x25mm - 100BAR
LED Autolamps 12/24V LED Stop/Tail/Indicator/Reverse Lamp 200x50x28mm Twin Blister - 200BIRSTME2
LED Autolamps 12/24V 280 Mini Jumbo Stop/Tail/Indicator/Reverse LED Light Blister Pack - 280ARWM
LED Autolamps Rear combination L/R tail lights with sequential indicator, Chrome, Twin Blister - 355ARWM-2
LED Autolamps 12V LED Stop/Tail/Indicator/Reverse Assemnly Lamp With 108 LEDs - 80BARW
LED Autolamps 90 Series Green Emergency LED Strobe/Warning Light 12V/24V Surface Mount - 90GM
LED Autolamps 12/24V LED Stop/Tail Lamp With Red Lens Round With Grommet/Plug - 113RMG
LED Autolamps 10/30V Rear Position Marker 2 Red LEDs With 40cm Wire Blister Pack - 58RM
LED Autolamps 10/30V Amber Emergency Light Bar Clear Lens With Amber LEDs 10 Selectable Flash Patterns - LB1345ACM
LED Autolamps 10/30V Amber Emergency Bar Clear Lens With Amber LEDs 19 Selectable Flash Patterns - LB964ACM
LED Autolamps 12/24V Amber LED Emergency Lamp With Strobe Permanent Mount - 93AM
LED Autolamps Multi Volt Stop/Tail/Indicator Lamp With Reflex Reflectors Grey Base Blister Pack 1 pce - 100ARM
LED Autolamps 355 Series Multi Volt Black Stop/Tail/Indicator/Reverse/Reflector LHS & RHS Twin Blister Pack - 355BARWM-2
1993 Nissan Primera headlights
Headlights are absolutely fitted to and relevant for the 1993 Nissan Primera (P10). This is documented in the Nissan Primera P10 factory service manual and owner’s manual lighting sections, and required by Australian Design Rules (ADR 13/00 and ADR 46/00) as well as New Zealand’s Land Transport Rule: Vehicle Lighting 2004. Those technical sources mandate compliant headlamps for safe road use, so this model ships with halogen headlights from factory.
On a ’93 Primera, the headlights do the heavy lifting for night driving and poor weather, projecting a legal beam pattern suited to right-hand-drive markets like Australia and New Zealand. The units are halogen reflector lamps, typically using an H4 60/55W dual‑filament bulb for low and high beam in one globe. Keeping them in good nick means better visibility, less fatigue, and a happier WOF or rego inspection.
When it’s time to replace a bulb, it’s a straightforward job under the bonnet. Access the rear of the headlamp, pop off the dust cap, unclip the spring retainer, and swap the H4 globe. Don’t touch the glass with bare fingers—oils shorten bulb life. Refit carefully, ensuring the rubber boot seals out moisture. It’s smart to replace bulbs in pairs so colour and brightness match. Stick with the factory wattage, higher-watt globes can overheat wiring and may not be ADR-compliant.
Routine care goes a long way. If the lenses have gone cloudy or yellow, a quality plastic headlight restoration kit can restore clarity—finish with a UV sealant to keep the haze away. Check connectors and earths for corrosion, a dodgy ground or voltage drop will make lights dim. If light output still feels weak after fresh bulbs and clean lenses, have the charging system tested and the headlight aim checked using proper equipment.
- Use ADR/UNECE-compliant H4 halogen bulbs for AU/NZ.
- Keep lenses clean, restore and seal if they’re hazed.
- Inspect fuses, connectors, and earth points during servicing.
- Have a workshop or WOF station verify beam aim and pattern.
What bulb type fits a 1993 Nissan Primera headlight?
Most P10 Primeras use an H4 60/55W halogen for combined low/high beam. Parking/position bulbs are usually W5W (T10). Always confirm against the owner’s manual or the existing bulb, as trims and markets can vary. Avoid non-approved HID/LED retrofits that can breach ADR/WOF requirements.
How does one adjust the headlight aim?
Use the vertical and horizontal adjusters on the back of each lamp. Park on level ground facing a wall, mark the cut-off, and make small changes. For best results—and to stay compliant—have a workshop or WOF inspector set the aim with a beam setter to the specifications in the service manual.
Why are the headlights dim or yellow?
Ageing halogen bulbs, UV-hazed plastic lenses, corroded earths, or voltage drop in old connectors are common culprits. Fit fresh quality H4 bulbs, restore the lenses with a sealant, and clean or repair wiring and grounds. If brightness is still off, get the alternator/charging voltage and beam aim checked.