Your Selected Vehicle
Filter
Filter By
Parts for your 1990 Suzuki Vitara-Headlights
LED Autolamps 12V Indicator Strip Lamp With 10 Square LEDs Recessed Mount - 235A12
LED Autolamps 10/30V LED Side Direction Indicator Light With 3m Tinned Cable - 58AM3
Narva Model 63 Front End Outline Marker, Side Indicator (Amber) Or External Cabin Marker Lamp Black Base And 0.5M Cable
LED Autolamps 12/24V LED Stop/Tail/Indicator/Reverse Lamp 200x50x28mm Twin Blister - 200BIRSTME2
LED Autolamps 12/24V Stop/Tail/Indicator/Reverse Lamp With Inbuild Reflectors - 283ARWM
LED Autolamps Rear combination L/R tail lights with sequential indicator, Chrome, Twin Blister - 355ARWM-2
LED Autolamps 8 Metre Boat Trailer Cable Tinned Copper Wiring And Side Marker/Licence Plate Light Connectors - BC800
Narva Model 70 Rear Stop/Tail/Indicator/Reverse Lamp With In-Built Retro Reflector, With 0.5M Of Cable - 97010-1
Narva Model 70 Rear Stop/Tail/Indicator/Reverse Lamp With In-Built Retro Reflector, With 0.5M Of Cable
LED Autolamps Multi Volt Stop/Tail/Indicator Lamp Black Bracket With 40cm Wire - 80BSTIM
LED Autolamps 12V LED Stop/Tail/Indicator Lamp With Reflex Reflector 2 Pack - 151BAR2
1990 Suzuki Vitara Headlights
Headlights are absolutely fitted to and relevant for the 1990 Suzuki Vitara. This is supported by the Suzuki Vitara/Sidekick Service Manual (1989–1995, Electrical: Lighting), the Suzuki Electronic Parts Catalogue listing headlamp assemblies and H4 globes for this model, and regulatory requirements such as Australian Design Rule 13/00 (installation of lighting) and New Zealand’s Land Transport Rule: Vehicle Lighting 2004, which mandate operational headlamps for on-road use.
On a 1990 Vitara, the headlights do the hard yards every day: they keep the road lit at night, make the vehicle visible in poor weather, and ensure it stays roadworthy for rego or WOF. Most Australasian Vitaras of this era run H4 60/55W halogen globes in composite headlamp housings, a few variants use sealed-beam units. A quick check of the lens marking (H4/HB2 or “sealed beam”) or the owner’s manual confirms what’s fitted.
When servicing, replacing headlight globes in pairs keeps beam colour and brightness even. Choose quality H4 halogens and avoid higher-wattage globes unless the car has upgraded relays and wiring, because extra heat and current can stress the switchgear. Replacement is straightforward: open the bonnet, unplug the three‑pin connector, peel back the rubber dust cap, release the spring clip, swap the globe, and refit in reverse. Don’t touch the glass—skin oils create hot spots, use gloves or a clean tissue. After any work, test both low and high beam and check the aim so oncoming drivers aren’t dazzled.
- Keep lenses clear: wash with mild car shampoo, if they’re hazed, use a plastic-safe restoration kit.
- Chasing dim lights? Inspect earth points and the headlight connectors for corrosion, and consider a relay harness to cut voltage drop—common on older wiring.
- Check the rubber dust caps and housing seals to keep moisture out. If condensation appears, air the unit and dry with silica gel before resealing.
- Aim matters: on level ground, 5–10 m from a wall, set the low-beam cutoff slightly below the lamp centreline. For ADR/WOF compliance, a workshop aim check is a smart move.
- Off-roading or water crossings? Make sure breathers are clear and mounts are tight so the lamps don’t shake out of alignment.
FAQs
What globe type fits a 1990 Suzuki Vitara?
Most AU/NZ-spec 1990 Vitaras use H4 60/55W halogen globes. If the lamp is marked as sealed beam, the entire unit is replaced instead of a globe. Always confirm by checking the lens marking or the owner’s manual.
Why are my Vitara’s headlights dim?
Ageing globes, hazy lenses, corroded earths, and voltage drop in old wiring are common causes. Clean the grounds, inspect connectors, consider a relay upgrade, and refresh the globes. Restoring the lens clarity often brings a big improvement.
How do I adjust the headlight aim?
Use the adjuster screws on the headlamp housing. Park on level ground 5–10 m from a wall, then set the low-beam cutoff just below the lamp centreline and slightly to the left. If unsure, have a workshop set the aim to meet ADR/WOF requirements.